Laminated goods with self-made illustrations, known as "lamikas," are easy to make, look good, and are very popular at coterie events. This section introduces how to make such lamikas. We have also included a video with easy-to-understand explanations, so if you would like to participate in doujin events or make your own goods, please check it out.
How to make Lamica
Cut out the illustration.
Heat up the laminator (turn it on)
Insert the illustration into the film.
Pass the entire film through the laminator.
In no time at all, a beautiful lamica is ready.
I don't have a laminator..!
Laminating film is a system that sticks together through "heat treatment.
In other words, it can be made without a specialized machine such as a laminator, depending on your efforts.
Iron on lamica.
I ironed it on and laminated it!
making.ti-da.net
I wanted to laminate a little card, so I experimented.
Preparation
Source: making.ti-da.net
Laminating
There seem to be several types, but I bought the common 100 micron type.
Iron
The one I always use.
Ironing board
I put down the cardboard boxes that I always put in my Amazon boxes.
Cooking sheet
Things don't stick to it and it is heat resistant.
Ironing and Laminating Tips and Tricks
Source: making.ti-da.net
Upon investigation, it seems that laminating machines crimp film at a heat of about 100℃.
This seems to be close to the lowest temperature you can get with an iron (low temperature of an iron: 80-120°C).
Turn on the iron, wait a few minutes, and then slide it on, pushing out the air in the laminate.
Source: making.ti-da.net
Measure the temperature of the iron.
The trick to laminating with an iron seems to be to apply it at the right temperature anyway.
Source: making.ti-da.net
If the temperature is too low, the milky white color of the sheet will not become transparent.
Conversely, if the temperature is too high, air bubbles will form, which will eventually expand.
Source: making.ti-da.net
It seems that wrinkles are less likely to appear if you apply the iron to the center first and then spread the iron over the edges.
So, we found that small cards can be laminated with a household iron.
Source: making.ti-da.net
It is worth a try when you want to pouch a small item.
I don't have a laminator or an iron! I want to make lamica more easily!
A good laminator is expensive, and I'll only use it once in a while...!
Laminating with an iron is also tricky and difficult..!
For those who are not so sure, there is a simple lamica kit available.
Available at 100 yen stores! Laminate (hand-applied)"
Source: nontansmade.blog.fc2.com
Daiso A4 laminating film
Because a thin film is placed over a thick film,
The finish was not firm.
To laminate firmly, it would be better to use two sheets of thick film and laminate them together.
Source: ameblo.jp
Postcard size 3 sheets / Nakatoshi Sangyo Co.
Purchased at Celia.
*Check with other 100 yen stores and office supply stores.
It is rather expensive considering the price of laminating film,
If you are making a small amount of Lamica, this may be more economical.
Making hand-applied laminates
Source: ameblo.jp
Peel off the film.
Insert the illustration.
Put the film on again.
Compared to laminators and iron-on laminating, this is very easy!
Weaknesses of 100-yen store laminates
Compared to lamica made with a laminator, it is
It is thin, not durable, and peels off at the worst possible time.
but can be handled with a few tricks.
Contents
- I want to laminate and make lamica! But...
- table of contents
- What is lamica (lamination)?
- Prepare items to be laminated
- paper
- art supplies
- When you are ready...
- When using a laminator
- What to prepare
- Laminating with a laminator
- I don't have a laminator..!
- Iron on lamica.
- I don't have a laminator or an iron! I want to make lamica more easily!
- Available at 100 yen stores! Laminate (hand-applied)"
- Making hand-applied laminates
- Weaknesses of 100-yen store laminates
- Is there anything easier to do than laminate from a 100 yen store?
- If you want durability, just make the "back side a clear file"!
- Laminating by myself is a hassle... I need somewhere to do it for me.
- I want to be able to use Lamica a little bit.
- summary
- Related Links
